Photos of your Airsoft equipment (Discussion)

Firekitten · 18-09-2009 12:21am

OzCam wrote: »

You're in a hole Rachel, stop digging.

Ah, grow a sense of humour :rolleyes:

Sam: Ja, sounds like they cut the spring to downgrade it. Best bet, is take it down and swap it out for a m100 for the vsr (actually fits fine) will be the right length, but not boingy.... If you want bullets, pm me and ill tell you how, save cluttering the thread.

Masada · 18-09-2009 1:02am

VSR springs are too short for it, it needs an APS2 type of spring.,

Firekitten · 18-09-2009 1:06am

Not so, they actually work Richie... its under less tension than an aps2 stacked, but its the right length when its screwd together in the cylinder... did it to a 96 for use over here.

Masada · 18-09-2009 1:08am

The spring thats in the barrett is an M100 VSR spring....

it fires at 1J but the spring is able to move, hence the noise bullets spoke of.

Firekitten · 18-09-2009 1:09am

mmm, interesting my mistake, perhaps you should use the correct parts for the job at Eiresoft then?

Masada · 18-09-2009 1:12am

as in,

the same parts you've just recommended?

Firekitten · 18-09-2009 1:14am

Well, yes, I've used it, and its not produced that issue in any of the rifles I did it to... But I did it to an aps2, sgg, and l96 models...

Though if it does this, and you know, Why havent you adressed it in your downgrade procedure?

Stercus Accidit · 18-09-2009 1:22am

Theres a trick involving balancing two springs, one weak and one strong either side of the piston head, you use a washer as a bushing for in front of the piston.

It also reduces noise if done right, as there is no frontal piston impact. I did it to the ssg(I know, muck) because it was hot as snot, needed half the spring off, and would have ended up with a spring way too short.

Bit of a custom job, but its pretty snaz the way it works. It depends how badly you want to reduce the piston noise and boing effect if you wanted a silent sniper for gaming, but a silent barret would be a bit sh1t.

Edit: lol, two lively posts appeared in the course of writing that, never mind me

/backs away slowly...

Firekitten · 18-09-2009 1:23am

As usual, nice idea sam

I like it.... May tinker with that one.

o1s1n · 18-09-2009 1:42am

Firekitten wrote: »

mmm, interesting my mistake, perhaps you should use the correct parts for the job at Eiresoft then?

Firekitten wrote: »

Though if it does this, and you know, Why havent you adressed it in your downgrade procedure?

I didn't realize this was the Eirsoft thread.

Oh wait, it's not.

Take it to the correct place and stop playing the wind up game.

I really like this thread. I read it daily. I think it's a great place to show off gear to new players and get them interested.

If I see people getting bitchy like this again with teh Drama I'll be handing out bans.

Shiva · 18-09-2009 2:04am

I'd really appreciate if ya'll spelt the goddamn name of the shop right

E.I.R.S.O.F.T.

Thanks

Masada · 20-09-2009 10:47pm

Holy sh1t puding, you can never again say there are too many M4 varients....

Puding · 20-09-2009 10:56pm

Masada wrote: »

Holy sh1t puding, you can never again say there are too many M4 varients....

i would not say that

but some armalites are finding there way into my collection, i'm currently working on a sopmod block 2 gbb based off the agm m4 (everyone seems to have a project with one of these on the go at the moment) should have all the parts by the end of the week

TheDoc · 20-09-2009 10:56pm

He does make me want to buy an AK in fairness....

Some **** sexy pieces there...

Horse84 · 21-09-2009 5:02pm

Puding wrote: »

i would not say that

but some armalites are finding there way into my collection, i'm currently working on a sopmod block 2 gbb based off the agm m4 (everyone seems to have a project with one of these on the go at the moment) should have all the parts by the end of the week

Kinda workin on something similar myself Puding, concentrating on upgrading all the internals first which is almost complete. Would love too see a list of the various parts you added when you have it finished, it might give me some inspiration:)

Masada · 21-09-2009 6:28pm

Some nice pieces there horse, i like the M9 in particular.,

Leftyflip · 21-09-2009 7:08pm

PornStar, that is one lovely looking gun, how much did it cost you?

defenderdude · 21-09-2009 7:19pm

Leftyflip wrote: »

PornStar, that is one lovely looking gun, how much did it cost you?

+1
Very nice job there Pornstar;)

-PornStar- · 21-09-2009 7:25pm

Leftyflip wrote: »

PornStar, that is one lovely looking gun, how much did it cost you?

defenderdude wrote: »

+1
Very nice job there Pornstar;)

Cheers, yeh I'm happy with how it turned out, though busy rails wont be to everyone's liking I'm sure. It cost a lot. Maybe close to a grand. It will be the last gun I buy for a long while..... hopefully.

Horse84 · 21-09-2009 7:47pm

Pornstar that's a credit to ya man absolutely beautiful job!

Masada wrote: »

Some nice pieces there horse, i like the M9 in particular.,

Cheers richie yea it's sweet to shoot as well and deadly accurate, it's showing some wear signs from the serpa now but i think it suits it. The grips are from a TM tactical master the i had lying around. The white trades kinda let it down and i can't for the life of me find a metal outer barrel for it but's top notch all the same:)