Labour Saving and General Guntering

Donald Trump

patsy_mccabe wrote: »

Anyone got a handy way of cutting an IPE200 girder at an angle other than using a bandsaw? I was looking at Chopsaws but they won't cut that big.

A bit of elbow grease and one of these











(joke of course)

blue5000

patsy_mccabe wrote: »

Ya, thinking about putting up a shed. :rolleyes: This is the last piece of the jigsaw.

Try work the lengths of the pillars out so that one angled cut does the tops of 2 pillars IYKWIM. What's the price of steel like these days?

emaherx

IMG_20200524_193854 by Emaherx, on Flickr

New poly tunnel under construction.

raypallas

patsy_mccabe wrote: »

Anyone got a handy way of cutting an IPE200 girder at an angle other than using a bandsaw? I was looking at Chopsaws but they won't cut that big.

9 inch grinder with the skinny stainless steel discs will cut through very easily and have the small grinder with a grinding disc to dress up the edges afterwards.

A lot of crowds will cut the top of the pillars to the correct pitch of your roof it you ask leaving only the trusses to be cut at the ends wouldn't have to be too accurate if it's just a lean too.

Kevhog1988

emaherx wrote: »

IMG_20200524_193854 by Emaherx, on Flickr

New poly tunnel under construction.

any more pics of the 135. She looks a clean one!!

emaherx

Kevhog1988 wrote: »

any more pics of the 135. She looks a clean one!!

Love this thread.......
It's always the back ground

Here you go
https://flic.kr/s/aHskthP6Q8

Kevhog1988

emaherx wrote: »

Love this thread.......
It's always the back ground

Here you go
https://flic.kr/s/aHskthP6Q8

Lovely tractor. Still at mine for about 5 yrs

emaherx

Kevhog1988 wrote: »

Lovely tractor. Still at mine for about 5 yrs

Like this one for me, some times other things get in the way


https://www.flickr.com/gp/14733679@N07/D959e5

patsy_mccabe

emaherx wrote: »

Like this one for me, some times other things get in the way


https://www.flickr.com/gp/14733679@N07/D959e5

That's one dirty sump filter. Was the torque convertor goosed in it?

emaherx

patsy_mccabe wrote: »

That's one dirty sump filter. Was the torque convertor goosed in it?

Don't believe I have a picture of the sump filter there.... Possibly the oil bath air breather? It was a bit smokey when I got it

Pump and drive lugs needed replacing. But I had only split it to do rope seal.

Haven't had time to look at it since little one was born and Dad passed away nearly 3 years ago.

Nekarsulm

Great photos, emaherx.
You'll get it finished yet, the back is broken on the work.

Anyone ever hear about Green Dragon, how things are going?

emaherx

Nekarsulm wrote: »

Great photos, emaherx.
You'll get it finished yet, the back is broken on the work.

Anyone ever hear about Green Dragon, how things are going?

I'm not too concerned. Had a very similar long pause with the 135, when the boys were born. I'm seeing a pattern there, I'll be very cautious about starting into another tractor.

Haven heard or seen anything from green dragon in a long while, be hard to compete with his work, he put a lot of time and effort into preserving original tin work.

_Brian

emaherx wrote: »

I'm not too concerned. Had a very similar long pause with the 135, when the boys were born. I'm seeing a pattern there, I'll be very cautious about starting into another tractor.

Haven heard or seen anything from green dragon in a long while, be hard to compete with his work, he put a lot of time and effort into preserving original tin work.

Great work there.

My wife says i only farm so I can break things and then spend the time fixing them since I don’t work at maintenance any more.

I think she may actually be right.

emaherx

_Brian wrote: »

Great work there.

My wife says i only farm so I can break things and then spend the time fixing them since I don’t work at maintenance any more.

I think she may actually be right.

Fixing stuff is the easy bit, painting small individual parts before reassembling can be torture. Sometimes I'm tempted to just put it back together the way it is but I'd probably regret it.

fastrac94

_Brian wrote: »

Great work there.

My wife says i only farm so I can break things and then spend the time fixing them since I don’t work at maintenance any more.

I think she may actually be right.

What kind of maintenance did you work at if ya don't mind me asking?

rushvalley

emaherx wrote: »

Love this thread.......
It's always the back ground

Here you go
https://flic.kr/s/aHskthP6Q8

Did you sell the cab? Or by any chance do you still have the support brackets for underneath the mudgaurds?

emaherx

rushvalley wrote: »

Did you sell the cab? Or by any chance do you still have the support brackets for underneath the mudgaurds?

I sold the cab. To someone on here.

Limestone Cowboy

Lads would any of ye have any ideas for covering a water tank 20ft x 17ft that wouldn't cost a fortune? Was thinking old slats but won't get them long enough. It won't be bearing any weight only its own. Just incase anyone would ever fall into it.

Odelay

Limestone Cowboy wrote: »

Lads would any of ye have any ideas for covering a water tank 20ft x 17ft that wouldn't cost a fortune? Was thinking old slats but won't get them long enough. It won't be bearing any weight only its own. Just incase anyone would ever fall into it.

Sheepwire?

patsy_mccabe

Limestone Cowboy wrote: »

Lads would any of ye have any ideas for covering a water tank 20ft x 17ft that wouldn't cost a fortune? Was thinking old slats but won't get them long enough. It won't be bearing any weight only its own. Just incase anyone would ever fall into it.

Drill tru holes near the top (before concrete sets fully), feed high tensile wire tru the holes and tension with a wire strainer like these;
https://www.goodwins.ie/products/Fencing-Ratchet-Wire-Strainer.html

Base price

Angle iron sections bolted down onto the concrete with heavy welded mesh.

dzer2

Put a railing along the top of the wall like a silage pit.

funkey_monkey

What happened here:

FB_IMG_15280922159792591 by Emaherx, on Flickr

cute geoge

Limestone Cowboy wrote: »

Lads would any of ye have any ideas for covering a water tank 20ft x 17ft that wouldn't cost a fortune? Was thinking old slats but won't get them long enough. It won't be bearing any weight only its own. Just incase anyone would ever fall into it.

Surely if it is wired off correctly with wire mesh this would be the standard procedure

emaherx

funkey_monkey wrote: »

What happened here:

FB_IMG_15280922159792591 by Emaherx, on Flickr

The story behind it is much worse than the picture.

Buford T. Justice XIX

emaherx wrote: »

The story behind it is much worse than the picture.

We have time on our hands....:pac:

emaherx

Buford T. Justice VI wrote: »

We have time on our hands....:pac:

Yes Sheriff that is my tractor, but at the time of the alleged incident I was neither owner or operator of the machine.

I was baling and another genius was drawing the bales out of the field. I was sent this picture and I couldn't figure out what had happened because that ditch is on the wrong side of the tractor.

So what happened is:
that's a very narrow private lane (stone surface hasn't seen much traffic since donkey and cart days) driver of the tractor was drawing bales out of the field lost a bale, which is no big deal, you'd leave it till later right. But no he decided he'd collect the bale on the way back to the field sure he'd collect it with just the right spike and keep coming without unhooking the trailer. As he drove along the side of the verge the bank collapsed and tractor and trailer went straight into the ditch.

The trailer had already been recovered when the picture was taken.

The operator of the tractor is reminded regularly that he is probably the only person in the history of farming to loose a tractor, trailer and a bale on the way back to a field and picture sent to him anytime he needs to be reminded of silly choices.

funkey_monkey

It was a reasonable plan until:

the bank collapsed

Sounds like something I'd attempt. :pac:

893bet

I was Guessing he was on tik tok and drove into the dyke.

emaherx

893bet wrote: »

I was Guessing he was on tik tok and drove into the dyke.

I doubt it, when that happened it would have taken 10 min to upload the still image to Bebo

Buford T. Justice XIX

emaherx wrote: »

I doubt it, when that happened it would have taken 10 min to upload the still image to Bebo

In my day, we'd have to wait to collect the photos from the chemist shop:D

Limestone Cowboy

cute geoge wrote: »

Surely if it is wired off correctly with wire mesh this would be the standard procedure

Ya it would probably be ok but would think it be a better job to have it covered as opposed to fenced off. Tank is 9ft deep and God fobid a young lad climbed over a fence and fell into it.

emaherx

Buford T. Justice VI wrote: »

In my day, we'd have to wait to collect the photos from the chemist shop:D

There is a major gap in photographic history where most photos taken at the end of the 90's and begining of the 00's are grainy and pixelated. Photos from the cheapest disposable 35mm film camera were far superior to early digital cameras and leagues ahead of early phone cameras.

49801

Limestone Cowboy wrote: »

Lads would any of ye have any ideas for covering a water tank 20ft x 17ft that wouldn't cost a fortune? Was thinking old slats but won't get them long enough. It won't be bearing any weight only its own. Just incase anyone would ever fall into it.

Steel grating / walkway. Beams required but straight forward and save to walk on

josephsoap

emaherx wrote: »

Yes Sheriff that is my tractor, but at the time of the alleged incident I was neither owner or operator of the machine.

I was baling and another genius was drawing the bales out of the field. I was sent this picture and I couldn't figure out what had happened because that ditch is on the wrong side of the tractor.

So what happened is:
that's a very narrow private lane (stone surface hasn't seen much traffic since donkey and cart days) driver of the tractor was drawing bales out of the field lost a bale, which is no big deal, you'd leave it till later right. But no he decided he'd collect the bale on the way back to the field sure he'd collect it with just the right spike and keep coming without unhooking the trailer. As he drove along the side of the verge the bank collapsed and tractor and trailer went straight into the ditch.

The trailer had already been recovered when the picture was taken.

The operator of the tractor is reminded regularly that he is probably the only person in the history of farming to loose a tractor, trailer and a bale on the way back to a field and picture sent to him anytime he needs to be reminded of silly choices.

You have the same tractor as myself, do you ever plan on moving on the 390T ?

Limestone Cowboy

49801 wrote: »

Steel grating / walkway. Beams required but straight forward and save to walk on

Ya the likes of that would be perfect. Would be easy enough run a few girders across the length of it to support them. I wonder where it could be got.

patsy_mccabe

Limestone Cowboy wrote: »

Ya the likes of that would be perfect. Would be easy enough run a few girders across the length of it to support them. I wonder where it could be got.

Heaton Buckley Limerick have them;
http://www.heitonsteel.ie/products/walkway

49801

Limestone Cowboy wrote: »

Ya the likes of that would be perfect. Would be easy enough run a few girders across the length of it to support them. I wonder where it could be got.

Be a few pound now... but a lifetime job!

Dinzee Conlee

49801 wrote: »

Be a few pound now... but a lifetime job!

Looks an expensive job...

Be cheaper to just put a galvanise roof on it would it?

emaherx

josephsoap wrote: »

You have the same tractor as myself, do you ever plan on moving on the 390T ?

There is too many old tractors with high hours here. I'd like something more modern eventually, but I think the 390T will be here for a long time. I'll probably sell the 698T and 365.

longgonesilver

What is the end use of the water?

A roof will help stop the water turning green,keep out wind blown debris and wildlife, as well as keeping swimmers out.

148multi

Limestone Cowboy wrote: »

Lads would any of ye have any ideas for covering a water tank 20ft x 17ft that wouldn't cost a fortune? Was thinking old slats but won't get them long enough. It won't be bearing any weight only its own. Just incase anyone would ever fall into it.

Set 3" tubing and tec screw secondhand cladding to the tubing.

Limestone Cowboy

longgonesilver wrote: »

What is the end use of the water?

A roof will help stop the water turning green,keep out wind blown debris and wildlife, as well as keeping swimmers out.

Maybe it will be good enough. Its a job we are doing for a fella, not my own. It's right beside the road and the top of the tank is below the level of it so it's dangerous enough. It's just a storage tank for watering cattle.

G-Man

Limestone Cowboy wrote: »

It's right beside the road and the top of the tank is below the level of it so it's dangerous enough .. and 9 ft deep!.

There you have it, the sorta destination I would have made a sunday out of investigating as a kid, and thankfully nothing happened.

You need to provide a proper job, I would say secure roof, factory style, you want to keep vermin out too. then some sort of access in case maintenance needed, that might mean galvanized platform just inside - perhaps safety ladder down into water.. Sounds like over doing it, but we all know how slatted tanks were as safe as houses.... until access is needed.

funkey_monkey

Where does the overflow go to?
How do you access it it empty it - can this be done quickly?

Steel checker plate is what I'd do it with. Although, not matter what you do, you'll need to have some central supports for whatever covering you're using. In that case could you not shutter a central column and span it with 3m pre-stressed lintels and then cover with the slats of your choice with a manhole to get a pipe in to empty it if required.

It's the sort of thing I'd prefer to do with a solid enclosure. But you're not the one pay the bill.

Limestone Cowboy

He's after ordering new precast slabs from McGraths for it. It's probably the best option.

Grueller

Limestone Cowboy wrote: »

He's after ordering new precast slabs from McGraths for it. It's probably the best option.

Expensive but a lifetime job. If its gravity filled even with the slabs of is cheap on the whole compared to well,pump,esb connections ongoing maintenance.

Limestone Cowboy

Grueller wrote: »

Expensive but a lifetime job. If its gravity filled even with the slabs of is cheap on the whole compared to well,pump,esb connections ongoing maintenance.

Ya it's gravity filled alright. Just a lot of people drawing off the same inch pipe and he's at the top of the hill, he has no water then in weather like this. Tank is standing about 5.5k. 12" walls and floor with a double row of 12mm mesh. It's nearly at the highest point on the farm so will be able to supply all the drinkers from a gravity flow aswell.

Kevhog1988

Myself and the uncle sandblasted and painted the chassis of the 135 today.

135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr
135 blast and paint by Kevin Hogan, on Flickr

Kevhog1988

Took this yesterday and thought ye would appreciate the uncles workbench

received_668389810682554 by Kevin Hogan, on Flickr