STOVES questions and answers here(see mod note in post 1)

therealmccoy

Cassette Stoves and Inset Stoves work exactly the same way; convection. And as long as you are comparing like for like (6kw vs 6kw) then the only difference will be brand/design.

Cassette stoves are a contemporary design and flush to the fireplace and typically give a large viewing pane while inset stoves typically come out 3/4 inches and are more traditional in design.

Vitae is a nice stove, but comes as standard as a Woodburning Stove. Make sure you get the Multifuel Kit with it. They've redesigned it recently to move the riddle and air controls to the side as opposed being operated via a lever which came through the glass. This works much better with the change.

Big Nelly wrote: »

Hey guys

Got a quote and more inline with what I am looking for, he is quoting the Vitae Cassette Stove. Says it is better than insert stove. Better heat.....

Just wondering has anyone a Vitae? are they a good job? I have never heard of them

Thanks
http://www.bpmsupplies.ie/vitaestove6kw.html

martinr5232

I fitted a hendly achill stove last week and put rock wool around the outer casing as i was advised but after a while there is an awful smell off the stove.

Can anyone tell me is there different types of insulation i could use ??

TTTT

martinr5232 wrote: »

I fitted a hendly achill stove last week and put rock wool around the outer casing as i was advised but after a while there is an awful smell off the stove.

Can anyone tell me is there different types of insulation i could use ??

Ceramic fiber blanket.

martinr5232

TTTT wrote:

Ceramic fiber blanket.

Any ideas where i could pick up some of that would it be something available in builders providers or is it a more specialised sort of thing ??

cocoman

martinr5232 wrote: »

Any ideas where i could pick up some of that would it be something available in builders providers or is it a more specialised sort of thing ??

Any decent stove shop should have it.

TTTT

martinr5232 wrote: »

Any ideas where i could pick up some of that would it be something available in builders providers or is it a more specialised sort of thing ??

pizzaovens4u.com/shop/item.aspx?itemid=9

I got some from them for my range. Great stuff and speedy delivery.

moonshadow

martinr5232 wrote: »

I fitted a hendly achill stove last week and put rock wool around the outer casing as i was advised but after a while there is an awful smell off the stove.

Can anyone tell me is there different types of insulation i could use ??

Hi Martin, there will be a smell off the stove for about 10 days, we used our one every day small fires just to eradicate the smell. It's mostly paint curing , grease ,new rope and cleaner burning off .
Give it a while all will be fine.

martinr5232

moonshadow wrote:

Hi Martin, there will be a smell off the stove for about 10 days, we used our one every day small fires just to eradicate the smell. It's mostly paint curing , grease ,new rope and cleaner burning off . Give it a while all will be fine.

This is really bad though its setting off the smoke alarm in the hall if the door is left open.

HeidiHeidi

martinr5232 wrote: »

This is really bad though its setting off the smoke alarm in the hall if the door is left open.

My stove stank to high heaven, gave me a blinding headache, and set off the smoke alarm without fail (although it was in the same room, in fairness, although down the other end of it) for about week. I had to open patio doors in late November! But all of a sudden one night it was fine.

Can't answer for your exact situation, but it's a possibility that it's still just the stove curing.

BarneyMc

Can anyone suggest makes of good wood burning stoves. I'm building a new house and have allowed for an external air supply. It's to heat a large room only and will be free standing. Thanks.

Big Nelly

therealmccoy wrote: »

Cassette Stoves and Inset Stoves work exactly the same way; convection. And as long as you are comparing like for like (6kw vs 6kw) then the only difference will be brand/design.

Cassette stoves are a contemporary design and flush to the fireplace and typically give a large viewing pane while inset stoves typically come out 3/4 inches and are more traditional in design.

Vitae is a nice stove, but comes as standard as a Woodburning Stove. Make sure you get the Multifuel Kit with it. They've redesigned it recently to move the riddle and air controls to the side as opposed being operated via a lever which came through the glass. This works much better with the change.

Thanks.....was wondering what the difference, guy was saying the cassette is better than a stove.

Blowheads

Big Nelly wrote: »

Thanks.....was wondering what the difference, guy was saying the cassette is better than a stove.

Just check the ash box on those (why we decided against), seemed very very small so depending on what you are burning of for how long might cause you some grief. the older model the grate riddle arm came out through the ash box, but the newer ones are at the side

Big Nelly

Blowheads wrote: »

Just check the ash box on those (why we decided against), seemed very very small so depending on what you are burning of for how long might cause you some grief. the older model the grate riddle arm came out through the ash box, but the newer ones are at the side

I dont mind ash box, in terms of the grate riddle, is this an issue with them? Thanks

Blowheads

you should care re ash box, esp if its overflowing every time you light the fire. riddle grate seemed ok

Big Nelly

Blowheads wrote: »

you should care re ash box, esp if its overflowing every time you light the fire. riddle grate seemed ok

I would guess I would only need to clear out every night? I must have a look somewhere

Blowheads

yep, have a look. it really depends on how much you burn and what your are burning
if running it for a long time with turf for example i could see it being a right pain as it would overflow and become a bit messy. dont under-estimate it

Hollywood130

Hello, I've been reading and reading and reading, just when I think I have made a decision I am told something else and everything goes to pot!! Would love some help and advice.

These are the radiators I need a stove to heat: 4 x 1400 Doubles, 1 x 1600 Double, 1 x 1200 Double, 2 x 1200 Singles, 1 x 600 Single. The radiators are 20inches in height. I've it down to 2 stoves. 1. Stanley Reginald, 2. Henley Blasket.

Stanley have told me that once we burn coal or anthracite the Reginald will be fine to heat what I need it to heat. Some of the Stanley stockists have said the Reginald would be at its limit and wouldn't really be sufficient. Some suggested the Henley which is a nice looking stove and quite similar to the Reginald. One other stockist told me the Reginald is much better than the Blasket stating it is 'a far superior stove' and that I should choose that over the Blasket.

The Blasket is about €500 cheaper but I would rather get whichever really is the better stove and will suit us. Can anyone shed any light?

therealmccoy

Based on my calculation, neither of those stoves are powerful enough to heat the rads you have listed. I estimate you need a stove with a power to heat the equivalent of 15rads plus hot water. So a stove with around 18-20kw to Water alone is what you need.

How big is the room you are putting it into?
At the minute, the Stratford EB20, Inis Mór mk2 (might be ok with Inis Meain mk2) and Henley Druid 25 would be my recommendations.

Hollywood130 wrote: »

Hello, I've been reading and reading and reading, just when I think I have made a decision I am told something else and everything goes to pot!! Would love some help and advice.

These are the radiators I need a stove to heat: 4 x 1400 Doubles, 1 x 1600 Double, 1 x 1200 Double, 2 x 1200 Singles, 1 x 600 Single. The radiators are 20inches in height. I've it down to 2 stoves. 1. Stanley Reginald, 2. Henley Blasket.

Stanley have told me that once we burn coal or anthracite the Reginald will be fine to heat what I need it to heat. Some of the Stanley stockists have said the Reginald would be at its limit and wouldn't really be sufficient. Some suggested the Henley which is a nice looking stove and quite similar to the Reginald. One other stockist told me the Reginald is much better than the Blasket stating it is 'a far superior stove' and that I should choose that over the Blasket.

The Blasket is about €500 cheaper but I would rather get whichever really is the better stove and will suit us. Can anyone shed any light?

Big Nelly

Quick question

I was with company earlier and they said if I use a timber outer frame, even if I replace the inner center piece I will not be insured anymore because I have replaced my fireplace with a stove and for a stove I need to have a marble type frame. They had no problem replacing it for 3000+

Is this correct? as per picture before the very outside frame is timber but rest would be currently steel but I am replacing this with the stove, putting in recommended unit by installer....he never mentioned I would need to change the outer timber frame....

therealmccoy

It is a pressing issue lately; the distance from a stove to a combustible surface.

In truth, you might never have an issue with the timber surround you have and a low heat output stove such as the Dimpex 4i or a Henley Apollo 5.
But if you cook those stoves, you'll find the underside of the mantle to get extremely hot. (And with wood being combustible, it is not unreasonable to assume that that could pose as a fire hazard).

It's almost getting to a stage where regulation will soon be here that no stove can be installed with a timber surround. But if in doubt, call your home insurance provider and see what their policy on it is. AFAIK, you need a VERY minimum of 300mm distance from any combustible surface.

Big Nelly wrote: »

Quick question

I was with company earlier and they said if I use a timber outer frame, even if I replace the inner center piece I will not be insured anymore because I have replaced my fireplace with a stove and for a stove I need to have a marble type frame. They had no problem replacing it for 3000+

Is this correct? as per picture before the very outside frame is timber but rest would be currently steel but I am replacing this with the stove, putting in recommended unit by installer....he never mentioned I would need to change the outer timber frame....

therealmccoy

I've attached an image showing the recommended distances from an inset stove to a combustible surface.

This was given to me by Henley.

Big Nelly

therealmccoy wrote: »

I've attached an image showing the recommended distances from an inset stove to a combustible surface.

This was given to me by Henley.

Perfect. Thanks....

rpmcs

Big Nelly wrote: »

Perfect. Thanks....

Just to note.... all stoves differ in distance to combustibles.
so for example
building regulations state min 300mm to nearest combustibles or stove manufacturer distance whichever is greater..
So timber surrounds depend on which stove you choose.

Tomc77

I just bought a house and am looking to replace a gas fire with a stove. I had a plumber?? out to look at it and he said it can't take a stove as the flue needs to be absolutely straight up to get any draw.

Sorry I don't have privileges to post a picture (not enough posts yet!)

The current set-up is that over the gas fire there is a space which which is connected to the chimney via a horizontal flue (about 1 foot long I guess). It would take a bit of work to remove all this and connect back into the chimney but the flue would never be straight up as the wall the stove is going on, is offset at at angle to the original fireplace.

Was the plumber right or is it worth pursuing the stove option. It you are angling a flue back into the chimney is there a maximum angle it can come off at. Really don't want to do all this work and end up with a useless stove. I will be getting it installed by a plumber.

Thanks

Dtp1979

Tomc77 wrote: »

I just bought a house and am looking to replace a gas fire with a stove. I had a plumber?? out to look at it and he said it can't take a stove as the flue needs to be absolutely straight up to get any draw.

Sorry I don't have privileges to post a picture (not enough posts yet!)

The current set-up is that over the gas fire there is a space which which is connected to the chimney via a horizontal flue (about 1 foot long I guess). It would take a bit of work to remove all this and connect back into the chimney but the flue would never be straight up as the wall the stove is going on, is offset at at angle to the original fireplace.

Was the plumber right or is it worth pursuing the stove option. It you are angling a flue back into the chimney is there a maximum angle it can come off at. Really don't want to do all this work and end up with a useless stove. I will be getting it installed by a plumber.

Thanks

45 degrees is the max angle you can use

Tomc77

Dtp1979 wrote: »

45 degrees is the max angle you can use

Thanks. How compromised would a stove (mainly burning coal) be if the angle was 45 Degrees?
Would you be better to try to break into the chimney higher up to keep the angle lower?

Hollywood130

therealmccoy wrote: »

Based on my calculation, neither of those stoves are powerful enough to heat the rads you have listed. I estimate you need a stove with a power to heat the equivalent of 15rads plus hot water. So a stove with around 18-20kw to Water alone is what you need.

How big is the room you are putting it into?
At the minute, the Stratford EB20, Inis Mór mk2 (might be ok with Inis Meain mk2) and Henley Druid 25 would be my recommendations.

Thanks, the plumber said 21kw would be what we need??? Wondering now.... the room is 19ft x 16ft. At least I have completely ruled out the Reginald. Can't believe Stanley don't do a bigger stove

Big Nelly

Going to go ahead with the Vitae 6kw cassette stove. Hopefully get it installed this week and will give some feedback.

I did notice when looking at one at weekend, there was multifuel kit installed but it is not totally metal internally. I looked at installation guide and they are firebrick. Do you know how many years before they have to be replaced?


http://www.bpmsupplies.ie/vitaestove6kw.html

therealmccoy

The firebrick will need to be replaced over time alright, but you should expect 5+ years before having to do that as long as you look after the stove and burn good clean dry fuel.

The firebrick is great at getting the heat out into the room much quicker than the cast-iron equivalent.

Big Nelly wrote: »

Going to go ahead with the Vitae 6kw cassette stove. Hopefully get it installed this week and will give some feedback.

I did notice when looking at one at weekend, there was multifuel kit installed but it is not totally metal internally. I looked at installation guide and they are firebrick. Do you know how many years before they have to be replaced?


http://www.bpmsupplies.ie/vitaestove6kw.html

Big Nelly

therealmccoy wrote: »

The firebrick will need to be replaced over time alright, but you should expect 5+ years before having to do that as long as you look after the stove and burn good clean dry fuel.

The firebrick is great at getting the heat out into the room much quicker than the cast-iron equivalent.

You mention good fuel, so plan on using logs but was going to get some coal as well. I seen the bargain forum thread about the coal from up north....so was going to buy in some bags. Based on option below I am going to go with the Champion Premium Coal, I guess this would be the best for stove?

Slack 40kg for €6
Amber King 40kg for €7
Champion Premium Coal 40kg for €8
Black Diamond Blend 40kg for €10 (semi smokeless)
Smokeless Ovoids 40kg for €12

therealmccoy

For any coal that cheap I'd be sceptical.
Not an advocate of burning coal at all, the only fuel I let near my fire is Kiln Dried Ash. Never Coal or Soaking wet petrol station wood.

Big Nelly wrote: »

You mention good fuel, so plan on using logs but was going to get some coal as well. I seen the bargain forum thread about the coal from up north....so was going to buy in some bags. Based on option below I am going to go with the Champion Premium Coal, I guess this would be the best for stove?

Slack 40kg for €6
Amber King 40kg for €7
Champion Premium Coal 40kg for €8
Black Diamond Blend 40kg for €10 (semi smokeless)
Smokeless Ovoids 40kg for €12

Big Nelly

therealmccoy wrote: »

For any coal that cheap I'd be sceptical.
Not an advocate of burning coal at all, the only fuel I let near my fire is Kiln Dried Ash. Never Coal or Soaking wet petrol station wood.

I wouldn't think that would be too cheap....

stesaurus

I'm renting a house so can't have a permanent fixture of a stove or make too many changes. So i want to have a stove sitting on the hearth with a rear flue exiting at at 45 degree to the chimney flue.

Found a good stove which suits my needs and can have a rear flue. The problem is that the flue is at the same height as part of the fireplace surround. I've attached a picture. The 'hood' is what gets in the way. Is there any way of temporarily removing that?

Big Nelly

s.welstead wrote: »

I'm renting a house so can't have a permanent fixture of a stove or make too many changes. So i want to have a stove sitting on the hearth with a rear flue exiting at at 45 degree to the chimney flue.

Found a good stove which suits my needs and can have a rear flue. The problem is that the flue is at the same height as part of the fireplace surround. I've attached a picture. The 'hood' is what gets in the way. Is there any way of temporarily removing that?

I have same problem, I am removing the surround and replacing....there is no other way to get around this....well from what I can see and also from the installer...

Unless you get a saw and cut it off of course, superglue is bound to work to put back on :P

therealmccoy

Is the hood bolted on or is it all one piece?

s.welstead wrote: »

I'm renting a house so can't have a permanent fixture of a stove or make too many changes. So i want to have a stove sitting on the hearth with a rear flue exiting at at 45 degree to the chimney flue.

Found a good stove which suits my needs and can have a rear flue. The problem is that the flue is at the same height as part of the fireplace surround. I've attached a picture. The 'hood' is what gets in the way. Is there any way of temporarily removing that?

stesaurus

therealmccoy wrote: »

Is the hood bolted on or is it all one piece?

I hadn't actually considered it might be bolted. I've just gone in and given it a good clean and managed to find three bolts. Cleaned it further and they are screwed in.
It might be difficult to get a screwdriver into the space but should be possible.

Thanks!

therealmccoy

Glad to have helped.

s.welstead wrote: »

I hadn't actually considered it might be bolted. I've just gone in and given it a good clean and managed to find three bolts. Cleaned it further and they are screwed in.
It might be difficult to get a screwdriver into the space but should be possible.

Thanks!

HeidiHeidi

s.welstead wrote: »

I'm renting a house so can't have a permanent fixture of a stove or make too many changes. So i want to have a stove sitting on the hearth with a rear flue exiting at at 45 degree to the chimney flue.

Found a good stove which suits my needs and can have a rear flue. The problem is that the flue is at the same height as part of the fireplace surround. I've attached a picture. The 'hood' is what gets in the way. Is there any way of temporarily removing that?

I had the same sort of fireplace (although square rather than round).

I have stood an Inis Airc stove in front of it, the flue comes out the back at the required angle, and off up the chimney with it. There's also the option for the flue to come out the top as well, which obviously didn't suit.

So maybe a different stove might make things simpler?

HeidiHeidi

s.welstead wrote: »

I'm renting a house so can't have a permanent fixture of a stove or make too many changes. So i want to have a stove sitting on the hearth with a rear flue exiting at at 45 degree to the chimney flue.

Found a good stove which suits my needs and can have a rear flue. The problem is that the flue is at the same height as part of the fireplace surround. I've attached a picture. The 'hood' is what gets in the way. Is there any way of temporarily removing that?

I thought I was going to have the same problem with my fireplace (although it's square rather than round).

I have stood an Inis Airc stove in front of it, the flue comes out the back at the required angle, and off up the chimney with it. There's also the option for the flue to come out the top as well, which obviously didn't suit.

So maybe a different stove might make things simpler?

SoapFan27

Hi,

If I was going for the Vitae 6KW cassette stove and didn't want a traditional fire surround etc, I've been told I could put in a granite tile surround. Has anyone got images of this? Can't find a whole lot online. Is this my only option? Thanks for any advice.

Bebop

therealmccoy wrote: »

For any coal that cheap I'd be sceptical.
Not an advocate of burning coal at all, the only fuel I let near my fire is Kiln Dried Ash. Never Coal or Soaking wet petrol station wood.

Do you find kiln dried ash is the best?

We have a Wanders inset wood burner and I have found that KD Oak is quite good but expensive, at present we are burning KD Beech, it burns quicker but is cheaper, Prices and quality seem to differ widely for the same type of wood,

mags16

SoapFan27 wrote: »

Hi,

If I was going for the RIVA 40 cassette stove and didn't want a traditional fire surround etc, I've been told I could put in a granite tile surround. Has anyone got images of this? Can't find a whole lot online. Is this my only option? Thanks for any advice.

I am getting a Riva 50 fitted next week. I didn't want a granite or slate surround because samples I saw were very thick. I've been told that you can use tile too, which is thinner. My worry was that the edge would look unfinished but I found this metal tile trim:

https://www.emctiles.co.uk/main/product/productinfo/985/Tile%20Trim%20Metal%20Straight%20Black%20ESA%2012mm/1

The idea is to use a border of 10cm black matt tile with dark grout all around the stove with the trim finishing off the edge. The stove will be raised about 50cm above the hearth with the wall below the stove built up and plastered. I want the tile border to look like an extension of the stove. The hearth is already recessed into the wood floor and the tiles in it will be replaced to match the ones around the stove.

I hope it looks ok.

trigger78

Tr 4kw insert stove any good and one any advice

SoapFan27

mags16 wrote: »

I am getting a Riva 50 fitted next week. I didn't want a granite or slate surround because samples I saw were very thick. I've been told that you can use tile too, which is thinner. My worry was that the edge would look unfinished but I found this metal tile trim:

https://www.emctiles.co.uk/main/product/productinfo/985/Tile%20Trim%20Metal%20Straight%20Black%20ESA%2012mm/1

The idea is to use a border of 10cm black matt tile with dark grout all around the stove with the trim finishing off the edge. The stove will be raised about 50cm above the hearth with the wall below the stove built up and plastered. I want the tile border to look like an extension of the stove. The hearth is already recessed into the wood floor and the tiles in it will be replaced to match the ones around the stove.

I hope it looks ok.

Thanks Mags, that sounds like a great idea. Would love to see pics when it's done if you want to share. thanks!

mags16

SoapFan27 wrote: »

Thanks Mags, that sounds like a great idea. Would love to see pics when it's done if you want to share. thanks!

Will do, SoapFan.

SoapFan27

Big Nelly wrote: »

Going to go ahead with the Vitae 6kw cassette stove. Hopefully get it installed this week and will give some feedback.

I did notice when looking at one at weekend, there was multifuel kit installed but it is not totally metal internally. I looked at installation guide and they are firebrick. Do you know how many years before they have to be replaced?


http://www.bpmsupplies.ie/vitaestove6kw.html

Got this stove recommended to me today by the chimney engineer that did an inspection, says he has one in his house and recommends it highly... look forward to the feedback.

Big Nelly

SoapFan27 wrote: »

Got this stove recommended to me today by the chimney engineer that did an inspection, says he has one in his house and recommends it highly... look forward to the feedback.

Its been installed on Friday.....

olestoepoke

Hi guys I've decided on a stratford eb 20 for my house. Does anyone know where i can take a look at the unit most places i call don't have one on display but can order for me. Also what do you guys think of this model cheers

olestoepoke

Big Nelly wrote: »

You mention good fuel, so plan on using logs but was going to get some coal as well. I seen the bargain forum thread about the coal from up north....so was going to buy in some bags. Based on option below I am going to go with the Champion Premium Coal, I guess this would be the best for stove?

Slack 40kg for €6
Amber King 40kg for €7
Champion Premium Coal 40kg for €8
Black Diamond Blend 40kg for €10 (semi smokeless)
Smokeless Ovoids 40kg for €12

Hi thats some great prices you quoted for fuel where is that available cheers

Big Nelly

olestoepoke wrote: »

Hi thats some great prices you quoted for fuel where is that available cheers

Thread on bargains forum, you need to order in pallet of coal from North....