Hkc 1070 mains fault

dave34k

Hi I have a hkc 1070 alarm. Can any one tell me should the alarm internal siren activated whan the main power goes off? I have a new battery in the alarm the buzzer goes in the key pad then the alarms activated

altor

dave34k wrote: »

Hi I have a hkc 1070 alarm. Can any one tell me should the alarm internal siren activated whan the main power goes off? I have a new battery in the alarm the buzzer goes in the key pad then the alarms activated

Other than the output for the internal bell has been changed to buzzer it should not happen

KoolKid

dave34k wrote: »

Hi I have a hkc 1070 alarm. Can any one tell me should the alarm internal siren activated whan the main power goes off? I have a new battery in the alarm the buzzer goes in the key pad then the alarms activated

What displays on the keypad when the system activates?

dave34k

KoolKid wrote: »

What displays on the keypad when the system activates?

Display Mains fault and on the key pad flashing power light and orange fault light and Red alarm light

KoolKid

You should get a keypad buzzer but there is no need for bells to activate.

dave34k

KoolKid wrote: »

You should get a keypad buzzer but there is no need for bells to activate.

How do I fix it

KoolKid

Hard to say without seeing the configuration and where the internal is wired to .
Do you have engineer code?

altor

dave34k wrote: »

How do I fix it

If you have engineer code go into the outputs menu, panel outputs.
Number 4 is the internal bell output.
Make sure this says internal bell.

dave34k

altor wrote: »

If you have engineer code go into the outputs menu, panel outputs.
Number 4 is the internal bell output.
Make sure this says internal bell.

Output menu . Panel output 4 is

altor

dave34k wrote: »

Output menu . Panel output 4 is

If you go into engineer mode, outputs menu, panel outputs, output 4 should be the internal bell.

dave34k

altor wrote: »

If you go into engineer mode, outputs menu, panel outputs, output 4 should be the internal bell.

Output menu
1 panel output is
01 pre alarm +ve
01 alarm+ve
05 external bell -ve.

2 expander output.

3 psu output.

4 output card output.

5 output groups.

5 user output

altor

dave34k wrote: »

Output menu
1 panel output is
01 pre alarm +ve
01 alarm+ve
05 external bell -ve.

2 expander output.

3 psu output.

4 output card output.

5 output groups.

5 user output

First 2 outputs are programmable outputs.
If you go into outputs it should be, 3 strobe, 4 internal and 5 external?

altor

An alternative option would be to use one of the free outputs and program this as the internal bell.

dave34k

altor wrote: »

If you go into engineer mode, outputs menu, panel outputs, output 4 should be the internal bell.

Output menu
1 panel output is
01 pre alarm +ve
01 alarm+ve
05 external bell -ve.

2 expander output.

3 psu output.

4 output card output.

5 output groups.

5 user output

altor

dave34k wrote: »

Output menu
1 panel output is
01 pre alarm +ve
01 alarm+ve
05 external bell -ve.

2 expander output.

3 psu output.

4 output card output.

5 output groups.

5 user output

Strange you have no strobe or internal in the panel outputs.
Have you an external bell on the system?

dave34k

altor wrote: »

First 2 outputs are programmable outputs.
If you go into outputs it should be, 3 strobe, 4 internal and 5 external?

1 01 pre alarm +
02 alarm +
03 strobe -
04 int bell -
05ext bell -
Thats what it said on the keypad.?

altor

dave34k wrote: »

1 01 pre alarm +
02 alarm +
03 strobe -
04 int bell -
05ext bell -
Thats what it said on the keypad.?

Thats what it should say.
Strange one as it should not be activating the internal bell.
Id try a software upgrade if needed then test.
Change output to a free one.
Other than that, Im at a loss as to why its happening.

dave34k

altor wrote: »

First 2 outputs are programmable outputs.
If you go into outputs it should be, 3 strobe, 4 internal and 5 external?

I turn off the main power on my Alarm now I am only getting a orange flashing light and a red Alarm flashing light but on inside siren??? Is that ok

altor

dave34k wrote: »

I turn off the main power on my Alarm now I am only getting a orange flashing light and a red Alarm flashing light but on inside siren??? Is that ok

No, keypad indications are correct but internal bell going off ain't. Id recommend getting an installer to have a look at it for you.

dave34k

dave34k wrote: »

I turn off the main power on my Alarm now I am only getting a orange flashing light and a red Alarm flashing light but on inside siren??? Is that ok

How do I upgrade my software? thanks for all your help I really apprecated it.

altor

dave34k wrote: »

How do I upgrade my software? thanks for all your help I really apprecated it.

Can only be done using smartlink 700.
Have you a GSM-SC installed?

dave34k

altor wrote: »

Can only be done using smartlink 700.
Have you a GSM-SC installed?

On GSMQ

altor

dave34k wrote: »

On GSMQ

Was you going to say I could do it remotely if you gave me access using the GSM-SC. Won't work with a GSM-Q. You would need an installer with smartlink 700 to do this for you.

dave34k

altor wrote: »

Was you going to say I could do it remotely if you gave me access using the GSM-SC. Won't work with a GSM-Q. You would need an installer with smartlink 700 to do this for you.

Ok so thanks for everything

altor

dave34k wrote: »

Ok so thanks for everything

No problem, sorry I couldn't help more