Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi all! We have been experiencing an issue on site where threads have been missing the latest postings. The platform host Vanilla are working on this issue. A workaround that has been used by some is to navigate back from 1 to 10+ pages to re-sync the thread and this will then show the latest posts. Thanks, Mike.
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Silicone bathtub question

  • 22-09-2020 1:17pm
    #1
    thepogues
    Registered Users Posts: 61 ✭✭


    Any advice appreciated. Photo is from where the bath edge meets the wall. (similar set up in the shower tray also) Does the sandy colored part need silicone or just the part in contact with the tiles? Thanks!


Comments

  • #2
    listermint
    Registered Users, Registered Users 2 Posts: 34,111 ✭✭✭✭listermint


    The part with the tiles . And you could put a small bit on the sandy part but the angle of fall should really move water away.

    Remember tape gives you a cleaner finish. Remove it before fully cured for clean lines.


  • #3
    thepogues
    Registered Users Posts: 61 ✭✭thepogues


    listermint wrote: »
    The part with the tiles . And you could put a small bit on the sandy part but the angle of fall should really move water away.

    Remember tape gives you a cleaner finish. Remove it before fully cured for clean lines.

    Ok thanks, any particular tape? (and any particular silicone?)


  • #4
    MAJJ
    Registered Users, Registered Users 2 Posts: 1,679 ✭✭✭MAJJ


    thepogues wrote: »
    Ok thanks, any particular tape? (and any particular silicone?)

    Also, wetting your finger in washing up liquid allows you to smooth off and correct the finish very easily, with little experience I could get clean lines and recover from mistakes from use of the silicone. Especially if you stop, strat or have excess or gaps.


  • #5
    Phil.x
    Registered Users, Registered Users 2 Posts: 1,749 ✭✭✭Phil.x


    thepogues wrote: »
    Any advice appreciated. Photo is from where the bath edge meets the wall. (similar set up in the shower tray also) Does the sandy colored part need silicone or just the part in contact with the tiles? Thanks!

    Those things are a nightmare, always leak.


  • #6
    thepogues
    Registered Users Posts: 61 ✭✭thepogues


    Phil.x wrote: »
    Those things are a nightmare, always leak.

    Better to put silicone on both sides so?


  • Advertisement
  • #7
    Phil.x
    Registered Users, Registered Users 2 Posts: 1,749 ✭✭✭Phil.x


    thepogues wrote: »
    Better to put silicone on both sides so?

    Before the tiles went on, a bead of silicone should be ran between bath and wall, then that plastic strip fixed to the wall and then tiled over leaving what you have in the photo. So if installed correctly it shouldn't leak, but they are an old way of sealing baths and showers and are nowadays seen as rubbish.

    For a quick fix if its leaking, silicone or tec7 where it meets the tiles and get a paint scraper or similar and lift it up and run some tec7 under it as it will probably be wet and silicone won't stick but tec7 will.


Advertisement