Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie

Cisco 1603 for netsmart?

Options
  • 24-10-2002 11:10am
    #1
    Grayarea
    Registered Users Posts: 246 ✭✭


    Hi all,

    I have a Cisco 1603 that I have been using without any problems with Eircom free net connection.

    I signed up for EsatBT Netsmart and having reporgrammed the router with the new dial up number and DNS servers I have the following problem.

    If I use CHAP then the line just toggles on demand, no connection gets established.

    If I use PAP then the line will establish but the server does not assign a IP address or gateway.

    Anyone got any ideas / tips?

    Thanks,

    Grayarea.


Comments

  • Options
    #2
    elmer
    Registered Users Posts: 732 ✭✭✭elmer


    you'd need to use chap for esat - give their support line a call on 1800 924 924 or send an email to support@esat.net and ask them for a sample router config in case you're missing something

    and yes they do reply to mail :)


  • Options
    #3
    cat5cowboy
    Closed Accounts Posts: 10 ✭cat5cowboy


    Use Chap.

    debug isdn events and then try and make a connection
    then do a show isdn status and paste the results.


  • Options
    #4
    Grayarea
    Registered Users Posts: 246 ✭✭Grayarea


    I am not familiar with all of the cisco commands, so whould I be right in doing the following?

    router>ena
    router>#debug isdn events
    router>#

    then try using web then

    router># show isdn stats

    Does that look right?

    I will try it when I get home.

    Thanks,

    Grayarea


  • Options
    #5
    spongebob
    Closed Accounts Posts: 6,143 ✭✭✭spongebob


    router>#show int bri0
    router>#show int bri1

    is it up or down after u dial

    (zero not ooh)


  • Options
    #6
    Grayarea
    Registered Users Posts: 246 ✭✭Grayarea


    It goes up and down very quickly. I see its state change if I have the console attached.

    bri0 is up (spoofing) when interogated.

    Later,

    Grayarea


  • Advertisement
  • Options
    #7
    Grayarea
    Registered Users Posts: 246 ✭✭Grayarea


    Here is a isdn debug

    Jpgroute#debug isdn events
    ISDN events debugging is on
    Jpgroute#
    00:03:03: ISDN BR0: Outgoing call id = 0x8001
    00:03:03: ISDN BR0: Event: Call id 0x8001 to 1332103001236 at 64 Kb/s
    00:03:03: ISDN BR0: Activating
    00:03:04: ISDN BR0: L1 is IF_ACTIVE
    00:03:04: ISDN BR0: Recvd MPH_EI2_IND from L1
    00:03:04: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 76 changed to up
    00:03:04: ISDN BR0: received HOST_INFORMATION call_id 0x8001
    00:03:04: ISDN Event: dsl 0 call_id 0x8001 B channel assigned by switch 0
    ISDN BR0: received HOST_CONNECT call_id 0x8001
    00:03:04: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:03:04: ISDN BR0: Event: Connected to 1332103001236 on B1 at 64 Kb/s
    00:03:05: ISDN BR0: received HOST_DISCONNECT call_id 0x8001
    00:03:05: ISDN BR0: Event: Call to <unknown> was hung up.
    00:03:05: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
    00:03:06: ISDN BR0: Outgoing call id = 0x8002
    00:03:06: ISDN BR0: Event: Call id 0x8002 to 1332103001236 at 64 Kb/s
    00:03:06: ISDN BR0: received HOST_INFORMATION call_id 0x8002
    00:03:06: ISDN Event: dsl 0 call_id 0x8002 B channel assigned by switch 0
    ISDN BR0: received HOST_CONNECT call_id 0x8002
    00:03:06: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:03:06: ISDN BR0: Event: Connected to 1332103001236 on B1 at 64 Kb/s
    00:03:07: ISDN BR0: received HOST_DISCONNECT call_id 0x8002
    00:03:07: ISDN BR0: Event: Call to <unknown> was hung up.
    00:03:07: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
    00:03:08: ISDN BR0: Outgoing call id = 0x8003
    00:03:08: ISDN BR0: Event: Call id 0x8003 to 1332103001236 at 64 Kb/s
    00:03:08: ISDN BR0: received HOST_INFORMATION call_id 0x8003
    00:03:08: ISDN Event: dsl 0 call_id 0x8003 B channel assigned by switch 0
    ISDN BR0: received HOST_CONNECT call_id 0x8003
    00:03:08: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:03:08: ISDN BR0: Event: Connected to 1332103001236 on B1 at 64 Kb/s
    00:03:09: ISDN BR0: received HOST_DISCONNECT call_id 0x8003
    00:03:09: ISDN BR0: Event: Call to <unknown> was hung up.
    00:03:09: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
    00:03:12: ISDN BR0: Outgoing call id = 0x8004
    00:03:12: ISDN BR0: Event: Call id 0x8004 to 1332103001236 at 64 Kb/s
    00:03:12: ISDN BR0: received HOST_INFORMATION call_id 0x8004
    00:03:12: ISDN Event: dsl 0 call_id 0x8004 B channel assigned by switch 0
    ISDN BR0: received HOST_CONNECT call_id 0x8004
    00:03:12: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:03:12: ISDN BR0: Event: Connected to 1332103001236 on B1 at 64 Kb/s
    00:03:13: ISDN BR0: received HOST_DISCONNECT call_id 0x8004
    00:03:13: ISDN BR0: Event: Call to <unknown> was hung up.
    00:03:13: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
    00:03:19: ISDN BR0: Outgoing call id = 0x8005
    00:03:19: ISDN BR0: Event: Call id 0x8005 to 1332103001236 at 64 Kb/s
    00:03:19: ISDN BR0: received HOST_INFORMATION call_id 0x8005
    00:03:19: ISDN Event: dsl 0 call_id 0x8005 B channel assigned by switch 0
    ISDN BR0: received HOST_CONNECT call_id 0x8005
    00:03:19: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:03:19: ISDN BR0: Event: Connected to 1332103001236 on B1 at 64 Kb/s
    00:03:20: ISDN BR0: received HOST_DISCONNECT call_id 0x8005
    00:03:20: ISDN BR0: Event: Call to <unknown> was hung up.
    00:03:20: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
    00:03:21: ISDN BR0: Outgoing call id = 0x8006
    00:03:21: ISDN BR0: Event: Call id 0x8006 to 1332103001236 at 64 Kb/s
    00:03:21: ISDN BR0: received HOST_INFORMATION call_id 0x8006
    00:03:21: ISDN Event: dsl 0 call_id 0x8006 B channel assigned by switch 0
    ISDN BR0: received HOST_CONNECT call_id 0x8006
    00:03:21: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:03:21: ISDN BR0: Event: Connected to 1332103001236 on B1 at 64 Kb/s
    00:03:22: ISDN BR0: received HOST_DISCONNECT call_id 0x8006
    00:03:22: ISDN BR0: Event: Call to <unknown> was hung up.
    00:03:22: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
    00:03:23: ISDN BR0: Outgoing call id = 0x8007
    00:03:23: ISDN BR0: Event: Call id 0x8007 to 1332103001236 at 64 Kb/s
    00:03:23: ISDN BR0: received HOST_INFORMATION call_id 0x8007
    00:03:23: ISDN Event: dsl 0 call_id 0x8007 B channel assigned by switch 0
    ISDN BR0: received HOST_CONNECT call_id 0x8007
    00:03:23: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:03:23: ISDN BR0: Event: Connected to 1332103001236 on B1 at 64 Kb/s
    00:03:24: ISDN BR0: received HOST_DISCONNECT call_id 0x8007
    00:03:24: ISDN BR0: Event: Call to <unknown> was hung up.
    00:03:24: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
    00:03:27: ISDN BR0: Outgoing call id = 0x8008
    00:03:27: ISDN BR0: Event: Call id 0x8008 to 1332103001236 at 64 Kb/s
    00:03:27: ISDN BR0: received HOST_INFORMATION call_id 0x8008
    00:03:27: ISDN Event: dsl 0 call_id 0x8008 B channel assigned by switch 0
    ISDN BR0: received HOST_CONNECT call_id 0x8008
    00:03:27: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:03:27: ISDN BR0: Event: Connected to 1332103001236 on B1 at 64 Kb/s
    00:03:33: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 1332103001236
    00:03:50: ISDN BR0: Event: Hangup call to call id 0x8008
    00:03:50: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 1332103001236 , call lasted 22 seconds
    00:03:50: ISDN BR0: received HOST_DISCONNECT_ACK call_id 0x8008
    00:03:50: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
    00:03:50: ISDN BR0: received HOST_DISCONNECT_ACK call_id 0x8008
    00:04:05: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 76 changed to down


  • Options
    #8
    Grayarea
    Registered Users Posts: 246 ✭✭Grayarea


    An here is some ppp packet info

    00:01:22: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 78 changed to up
    00:01:22: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
    00:01:22: BR0:1 LCP: O CONFREQ [Closed] id 1 len 10
    00:01:22: BR0:1 LCP: MagicNumber 0x507465A9 (0x0506507465A9)
    00:01:22: BR0:1 PPP: I pkt type 0xC021, datagramsize 32
    00:01:22: BR0:1 PPP: I pkt type 0xC021, datagramsize 14
    00:01:22: BR0:1 LCP: I CONFREQ [REQsent] id 4 len 28
    00:01:22: BR0:1 LCP: AuthProto PAP (0x0304C023)
    00:01:22: BR0:1 LCP: MagicNumber 0x199FA17D (0x0506199FA17D)
    00:01:22: BR0:1 LCP: MRRU 1524 (0x110405F4)
    00:01:22: BR0:1 LCP: EndpointDisc 1 Local (0x130A0171756172313631)
    00:01:22: BR0:1 LCP: O CONFREJ [REQsent] id 4 len 18
    00:01:22: BR0:1 LCP: MRRU 1524 (0x110405F4)
    00:01:22: BR0:1 LCP: EndpointDisc 1 Local (0x130A0171756172313631)
    00:01:22: BR0:1 LCP: I CONFACK [REQsent] id 1 len 10
    00:01:22: BR0:1 LCP: MagicNumber 0x507465A9 (0x0506507465A9)
    00:01:22: BR0:1 PPP: I pkt type 0xC021, datagramsize 18
    00:01:22: BR0:1 LCP: I CONFREQ [ACKrcvd] id 5 len 14
    00:01:22: BR0:1 LCP: AuthProto PAP (0x0304C023)
    00:01:22: BR0:1 LCP: MagicNumber 0x199FA17D (0x0506199FA17D)
    00:01:22: BR0:1 LCP: O CONFNAK [ACKrcvd] id 5 len 9
    00:01:22: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
    00:01:22: BR0:1 PPP: I pkt type 0xC021, datagramsize 18
    00:01:22: BR0:1 LCP: I CONFREQ [ACKrcvd] id 6 len 14
    00:01:22: BR0:1 LCP: AuthProto PAP (0x0304C023)
    00:01:22: BR0:1 LCP: MagicNumber 0x199FA17D (0x0506199FA17D)
    00:01:22: BR0:1 LCP: O CONFNAK [ACKrcvd] id 6 len 9
    00:01:22: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
    00:01:23: BR0:1 PPP: I pkt type 0xC021, datagramsize 18
    00:01:23: BR0:1 LCP: I CONFREQ [ACKrcvd] id 7 len 14
    00:01:23: BR0:1 LCP: AuthProto PAP (0x0304C023)
    00:01:23: BR0:1 LCP: MagicNumber 0x199FA17D (0x0506199FA17D)
    00:01:23: BR0:1 LCP: O CONFNAK [ACKrcvd] id 7 len 9
    00:01:23: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
    00:01:23: BR0:1 PPP: I pkt type 0xC021, datagramsize 18
    00:01:23: BR0:1 LCP: I CONFREQ [ACKrcvd] id 8 len 14
    00:01:23: BR0:1 LCP: AuthProto PAP (0x0304C023)
    00:01:23: BR0:1 LCP: MagicNumber 0x199FA17D (0x0506199FA17D)
    00:01:23: BR0:1 LCP: O CONFNAK [ACKrcvd] id 8 len 9
    00:01:23: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
    00:01:23: BR0:1 PPP: I pkt type 0xC021, datagramsize 18
    00:01:23: BR0:1 LCP: I CONFREQ [ACKrcvd] id 9 len 14
    00:01:23: BR0:1 LCP: AuthProto PAP (0x0304C023)
    00:01:23: BR0:1 LCP: MagicNumber 0x199FA17D (0x0506199FA17D)
    00:01:23: BR0:1 LCP: O CONFNAK [ACKrcvd] id 9 len 9
    00:01:23: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
    00:01:23: BR0:1 PPP: I pkt type 0xC021, datagramsize 8
    00:01:23: BR0:1 PPP: I pkt type 0xC021, datagramsize 18
    00:01:23: BR0:1 LCP: I TERMREQ [ACKrcvd] id 10 len 4
    00:01:23: BR0:1 LCP: O TERMACK [ACKrcvd] id 10 len 4
    00:01:23: BR0:1 LCP: I CONFREQ [REQsent] id 11 len 14
    00:01:23: BR0:1 LCP: AuthProto PAP (0x0304C023)
    00:01:23: BR0:1 LCP: MagicNumber 0x199FA17D (0x0506199FA17D)
    00:01:23: BR0:1 LCP: O CONFREJ [REQsent] id 11 len 8
    00:01:23: BR0:1 LCP: AuthProto PAP (0x0304C023)
    00:01:23: BR0:1 PPP: I pkt type 0xC021, datagramsize 8
    00:01:23: BR0:1 LCP: I TERMACK [REQsent] id 11 len 4
    00:01:23: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down


  • Options
    #9
    Grayarea
    Registered Users Posts: 246 ✭✭Grayarea


    Esat support have come back to tell me that I need to upgrade to IOS 12.1

    I will update when I have done this.

    Grayarea.


  • Options
    #10
    Grayarea
    Registered Users Posts: 246 ✭✭Grayarea


    I have attached a copy of the working config for Netmart below.

    There was no need to update IOS on the router, it is now working with 11.3.

    I used Cisco configmaker to rebuild a config from scratch for Netsmart and it worked with no problems.

    There does not seem to be much differance between this working and the non working config besides configuring CHAp and PAP.

    Thanks for all the suggestions and comments. :)

    Grayarea.


Advertisement